Flex-a-lite 56484 Camaro Radiator and Fan Combo Fits 1982-1992 Manuel d'utilisateur télécharger pdf

Camaro Radiator and Fan Combo #56484

Fits 1982-1992

INSTALLATION INSTRUCTIONS

REMOVAL OF EXISTING FAN AND SHROUD ASSEMBLY: NOTE:Your vehicle components may very

1. Make sure the engine is cool!

2. Disconnect negative (-) battery cable from battery.

3. Remove “Z” shaped air ducting between air filter canister and flexible air duct. Note: If your vehicle

comes equipped with a strait forward or other air ducting configuration, remove it. (see detail 1a)

4. Remove remaining flexible air duct attached to intake manifold. Remove intergraded tube leading to

passenger side valve cover. (see detail 1a)

5. Remove air ducting support bracket from top radiator bracket, and remove or detach Air Conditioning

(A/C) lines from shroud.

6. Pull A/C lines away from top of radiator and hold in place over motor; this gets the hoses out of the way

for better access. Tip: Try using long zip ties to secure loose objects in place as needed.

7. Remove electric fan or clutch fan at this time

8. Release wire loom from mounts on lower metal support bracket (supporting bottom radiator hose). Pull

bottom radiator hose out of bracket. (see detail 2)

9. Remove the bolts holding together the following items:

a. Power steering cooling lines.

b. Lower frame cross member.

c. Plastic bottom fan bracket. Note: You later will be reusing metal support bracket, plastic bottom

fan bracket and bolts during new radiator/ electric fan installation. (see detail 7)

14. Remove radiator cap and drain radiator; drain valve on passenger side at bottom.

Flexible air duct

(Detail 1a)

Top radiator bracket

(Detail 1b)

Rev. 09-14-09 #99484 Page 1 of 5

(Detail 2)

Wire loom

mounts

Wire loom

15. Disconnect the following:

a. Overflow hose leading to coolant reservoir.

b. Bottom radiator hose from radiator and let remaining coolant drain.

c. Top radiator hose from radiator.

16. Remove the bolts (4) securing top radiator bracket to top cross member and top of radiator. Note: Save

the bolts to be reused later. (see detail 1b on page 1)

17. Pull the original radiator up & out from the engine compartment then set it aside. (see detail 3)

18. Clean out any debris (leaves, bugs, dirt, coolant) from bottom cross member where original radiator use

to rest.

(Detail 3)

Showing lower

cross member w/

radiator removed

Clean debris

from this space

1 2 3 4 5

Résumé du contenu

Page 1 - INSTALLATION INSTRUCTIONS

Camaro Radiator and Fan Combo #56484Fits 1982-1992INSTALLATION INSTRUCTIONSREMOVAL OF EXISTING FAN AND SHROUD ASSEMBLY: NOTE:Your vehicle components m

Page 2 - (Detail 7)

INSTALLATION OF NEW FAN AND SHROUD ASSEMBLY:1. Start by removing the bottom rubber radiator mounts. Trim the rubber mounts flat across the top toallow

Page 3

11. Attach bracket #56404, on top of bracket #56403, on driver’s side. You will need to remove,and then reinstall, a bolt previously installed in step

Page 4 - Fan Wiring Instructions

Fan Wiring InstructionsFOLLOW THESE INSTRUCTIONS CAREFULLY TO AVOID DAMAGING THE CONTROL UNIT,FAN MOTORS, AND YOUR VEHICLE! WHEN CRIMPING WIRES, ALWAY

Page 5

The Flex-a-lite Limited WarrantyFlex-a-lite Consolidated, 7213-45th St. Ct. E. Fife, WA 98424, Telephone No. 253-922-2700, warrants to the original pu

Commentaires sur ces manuels

Pas de commentaire

Flex-a-lite 56484 Camaro Radiator and Fan Combo Fits 1982-1992 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Flex-a-lite 56484 Camaro Radiator and Fan Combo Fits 1982-1992. Flex-a-Lite 56484 Camaro Radiator and Fan Combo Fits 1982-1992 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Flex-a-lite 56484 Camaro Radiator and Fan Combo Fits 1982-1992